Toyota Avalon 2nd Gen (xx20) 1994 to 2004

 

  • Procedure

 

NOTE :To program the remote transmitters the PRG(Program) circuit of the Wireless Door Lock ECU

requires grounding. This can be performed by locating the Light Failure Sensor located in the trunk/boot

near the left hinge.

 

NOTE : Maximum 2 remote control transmitters can be programmed.

 

  1. With the ignition KEY out, disconnect the Light Failure Sensor harness.

 

  1. Using a suitable jumper/wire cable connect Terminal 12 (PRG) to Terminal 11 (GND)

 

NOTE : Please see picture for wire colours and connector layout.

 

  1. The doors will LOCK and UNLOCK, to confirm programming mode has been selected, it will also activate the

trunk/boot opening motor.

 

  1. Press any button on the first remote transmitter to be programmed, the doors will LOCK and UNLOCK to

confirm programing is a success.

 

  1. Repeat step 4 for additional remote transmitter.

 

  1. Disconnect jumper/wire.

RS3000 (VIP)

 

DEALER FITTED REMOTE KEYLESS ENTRY PROGRAMMING

 

NOTE : Maximum of 8 remote transmitters can be programmed.

 

NOTE : From 1998 MY the remote transmitters were updated from BLACK to GREY. The new GREY remote transmitters will not work on the older vehicles.

 

ADD REMOTE TRANSMITTER

 

  1. Locate the RS3000 ECU.

 

The ECU locations are as follows :

 

4runner(1999MY) : Behind panel right hand side of steering wheel, older models under drivers seat.

Avalon : Under passenger seat.

Camry (1998/1999MY) Older models located under drivers seat.

Celica : Under drivers seat.

Corolla : Under drivers seat.

RAV4 : Under drivers seat.

Sienna : Behind panel right hand side of steering wheel.

Solara : Centre console in storage compartment.

T100 : Under drivers seat.

Tacoma : Under drivers seat.

Tercal : Under drivers seat.

 

  1. Insert ignition key, and turn ON.
  2. PRESS and HOLD the ECU PROGRAMMING SWITCH for 3 seconds (Located on the side of the ECU)

 

NOTE : The STATUS MONITOR LED will light for 5 seconds.

 

NOTE : Please perform the next step within 5 seconds.

 

  1. PRESS and release either button on the remote transmitter.

 

NOTE : The STATUS MONITOR LED will turn OFF and the sounder will sound once.

 

  1. Turn OFF the ignition, the remote transmitter is now programmed.

 

ERASE ALL REMOTE TRANSMITTERS

 

  1. Insert ignition key, and turn ON.

 

  1. PRESS and HOLD the ECU PROGRAMMING SWITCH for 3 seconds (Located on the side of the ECU)

 

NOTE : The STATUS MONITOR LED will light for 5 seconds.

 

NOTE : Please perform the next step within 5 seconds.

 

  1. PRESS and HOLD the ECU PROGRAMMING SWITCH for 3 seconds.

 

NOTE : The STATUS MONITOR LED will flash 3 times, and the sounder will sound 3 times.

 

  1. Turn ignition OFF, all remote transmitters are now erased.

 

RS3200

 

DEALER FITTED REMOTE KEYLESS ENTRY PROGRAMMING

 

 

RS3200 (TVIP)

 

DEALER FITTED REMOTE KEYLESS ENTRY PROGRAMMING

 

NOTE : Maximum of 4 remote transmitters can be programmed.

 

NOTE : When a new remote transmitter it will be programmed in normal mode, additional options for this system

can be setup by referring to the main operating manual of this system.

 

  1. Open the drivers door and remove the ignition key.

 

  1. The programming steps must be performed within 40 seconds.

 

  1. Insert the key into the ignition 2 times.

 

  1. Close then open the drivers door 2 times.

 

  1. Insert the key into the ignition 1 time.

 

  1. Close then open the drivers door 2 times.

 

  1. Insert the key into the ignition and leave it in.

 

  1. Close the drivers door.

 

  1. Turn the ignition key from LOCK to ON, and then back to LOCK position.

 

  1. Remove the key.

 

  1. The tail/rear lights will flash once, the sounder will sound once and the doors willLOCK and UNLOCK.

 

  1. Press theLOCK and UNLOCK button once together on the remote transmitter to be programmed.

 

  1. Press theLOCK button on the remote transmitter.

 

  1. The tail/rear lights will flash once, the sounder will sound once and the doors willLOCK and UNLOCK.

 

  1. Repeat steps 12 to 14 for any additional remote transmitters.

 

  1. Open thedrivers door.

 

TO ERASE AND PROGRAM EXISTING REMOTE TRANSMIITERS

 

  1. Open the drivers door and remove the ignition key.

 

  1. The programming steps must be performed within 40 seconds.

 

  1. Insert the key into the ignition 2 times.

 

  1. Close then open the drivers door 2 times.

 

  1. Insert the key into the ignition 1 time.

 

  1. Close then open the drivers door 2 times.

 

  1. Insert the key into the ignition and leave it in.

 

  1. Close the drivers door.

 

  1. Turn the ignition key from LOCK to ON, and then back to LOCK position 2 times.

 

  1. REMOVE the key.

 

  1. The tail/rear lights will flash once, the sounder will sound once and the doors will LOCK and UNLOCK.

 

  1. PRESS the LOCK and UNLOCK button once together on the remote transmitter to be programmed.

 

  1. PRESS the LOCK button on the remote transmitter.

 

  1. The tail/rear lights will flash once, the sounder will sound once and the doors will LOCK and UNLOCK.

 

  1. Repeat steps 12 to 14 for any additional remote transmitters.

 

  1. OPEN the drivers door.

 

  1. LOCK and UNLOCK the doors using the drivers door LOCK button 5 times.

 

  1. Insert key into ignition and turn to the ON position 2 times, then remove the key.

 

  1. LOCKS should cycle from LOCK to UNLOCK to confirm programming.

 

  1. Press the LOCK and UNLOCK button together on the remote transmitter for 1 second.

 

  1. TheLOCKS should cycle LOCK to UNLOCK to confirm programming.
Toyota Avensis Toyota Aurion Toyota Avalon
Toyota Camry Toyota Corolla Toyota Coaster
Toyota FJ Cruiser Toyota Hiace Toyota Townace
Toyota Liteace Toyota Hilux Toyota Land Cruiser
Toyota Land Cruiser Prado Toyota Kluger Toyota Fortuner
Toyota Previa Toyota Prius Toyota Tarago
Toyota Yaris Toyota Dyna